Replacing the fan bearing on my 1965 110. I purchased the already attached fan bearing & case cover combo from Clark's, and am down to where I've removed the 4 screws going into the pulley. I've managed to remove everything else (carbs, shroud cover etc), up till now.
Do I remove the fan using a puller?
I've read in my research that the fan itself should lift off once the pulley is removed, but a puller is the only way I can think of to get the pulley off.
As you can assume, I'm relatively new to doing mechanical work, and I've tried searching the forum and looking in my manuals, but can't find anything specific to my question.
Thanks for your help.
Replacing engine fan bearing question
Replacing engine fan bearing question
1962 Monza 900
Re: Replacing engine fan bearing question
The pulley should just come right off after you remove the four bolts. You may have to tap it with a rubber mallet to jar it loose?
Scott
1960 Monza Coupe
1965 Evening Orchid Corsa Turbo (project)
1961 Rampside (project)
1964 Spyder coupe (patina car, running)
1964 faux Spyder (project/parts car)
1964 Monza (parts car)
1963 Monza (parts car)
1960 Monza Coupe
1965 Evening Orchid Corsa Turbo (project)
1961 Rampside (project)
1964 Spyder coupe (patina car, running)
1964 faux Spyder (project/parts car)
1964 Monza (parts car)
1963 Monza (parts car)
- terribleted
- Posts: 4584
- Joined: Sun Apr 18, 2010 2:36 pm
- Location: Atlanta, GA
- Contact:
Re: Replacing engine fan bearing question
Once the 4 bolts are removed the pulley should come off and then the fan should come off. They get stuck sometimes. Spray with some type of break free solvent like PB blaster and as mentioned above some tapping may be needed to loosen the corrosion and crude holding it in place.
Corvair guy since 1982. I have personally restored at least 20 Vairs, many of them restored ground up.
Currently working full time repairing Corvairs and restoring old cars.
https://www.facebook.com/tedsautorestoration/
Located in Snellville, Georgia
Currently working full time repairing Corvairs and restoring old cars.
https://www.facebook.com/tedsautorestoration/
Located in Snellville, Georgia
Re: Replacing engine fan bearing question
Just went through this myself. The pulleys can get stuck on there so tight that you would think they were welded on.
Use penetrating oil and gently rock the pulley back and forth or tap gently with a soft mallet side to side as mentioned. Once you see the slightest wiggle you know you will get there but go slow and it will eventually come off.
The fan itself usually comes off easily once the pulley is out of the way. I've never had to use a puller on either and would be afraid of causing damage if I tried.
Use penetrating oil and gently rock the pulley back and forth or tap gently with a soft mallet side to side as mentioned. Once you see the slightest wiggle you know you will get there but go slow and it will eventually come off.
The fan itself usually comes off easily once the pulley is out of the way. I've never had to use a puller on either and would be afraid of causing damage if I tried.
Dave W. from Gilbert, AZ
66 Corsa 140/4 Yenko Stinger Tribute
66 Corsa 140 Coupe w/factory A/C
65 Monza 4DR 140/PG w/factory A/C
65 Monza 4DR EJ20T/5
64 Greenbrier 110/PG, Standard 6-Door
66 Corsa 140/4 Yenko Stinger Tribute
66 Corsa 140 Coupe w/factory A/C
65 Monza 4DR 140/PG w/factory A/C
65 Monza 4DR EJ20T/5
64 Greenbrier 110/PG, Standard 6-Door