Search found 883 matches
- Mon May 20, 2019 12:56 pm
- Forum: Member's Rides, Projects, and Builds
- Topic: Noisy Lifter
- Replies: 7
- Views: 934
Re: Noisy Lifter
I have one lifter that will clatter for a few minutes after sitting for a while, must have shut down with it open and it bleeds down over a few days. A few minutes and it quiets down. Doesn't happen all the time.
- Wed May 15, 2019 2:35 am
- Forum: Member's Rides, Projects, and Builds
- Topic: 1965 Corsa clone, but a sweeeeeet one
- Replies: 305
- Views: 64762
Re: 1965 Corsa clone, but a sweeeeeet one
Yes, I do have the uni-syn and I do check balance both at idle and off-idle. Just didn't open it enough there to spot the clip removal goof. It's all good now. I will return to Roger's linkage now that I have everything working well on the stock linkage.
- Thu May 09, 2019 6:38 pm
- Forum: Member's Rides, Projects, and Builds
- Topic: Its been awhile!!
- Replies: 29
- Views: 3984
Re: Its been awhile!!
I had an issue where the plug wire for #2 cylinder failed so that side would stay choked since that's right where the choke coil lives, thankfully didn't take long to figure that out, but it sounds like it's still a carb issue on that side.. do you have a Uni-Syn?
- Thu May 09, 2019 6:33 pm
- Forum: Member's Rides, Projects, and Builds
- Topic: 1965 Corsa clone, but a sweeeeeet one
- Replies: 305
- Views: 64762
Re: 1965 Corsa clone, but a sweeeeeet one
The solution was mundane.. when I squeezed the u shaped gap on the primary carb that controls the fast idle to decrease it and lower the fast idle, the upper part moved both down and out, rubbing against and handily removing the lower retaining clip from the throttle link. I was trying to accelerate...
- Thu May 09, 2019 9:20 am
- Forum: Member's Rides, Projects, and Builds
- Topic: 1965 Corsa clone, but a sweeeeeet one
- Replies: 305
- Views: 64762
Re: 1965 Corsa clone, but a sweeeeeet one
I decided to adjust the fast idle a bit and turn the idle mixture screws in a bit more this morning, and drive the car to work to see how it liked the changes. I could tell something was off beyond a possibly slightly lean idle mixture. Had no time to troubleshoot before work, but suspect the "...
- Wed May 08, 2019 11:02 am
- Forum: Member's Rides, Projects, and Builds
- Topic: 1965 Corsa clone, but a sweeeeeet one
- Replies: 305
- Views: 64762
Re: 1965 Corsa clone, but a sweeeeeet one
Balanced the carbs, and now I also have a LOT more fast idle when cold that I did before, when the section of the throttle link that touches the fast idle cam gap was different between primary carbs so only one was really even touching the cam when the chokes were shut. Have turned the choke links d...
- Tue May 07, 2019 2:21 pm
- Forum: Member's Rides, Projects, and Builds
- Topic: 1965 Corsa clone, but a sweeeeeet one
- Replies: 305
- Views: 64762
Re: 1965 Corsa clone, but a sweeeeeet one
I had a occasional hot start problem recently, and I think I found the issue being a slightly sticky primary float. I also did some minor adjustments on choke tangs on the throttle attachment so both primaries are open the same amount when on the same fast idle tang. One was clearly not opening as m...
- Tue Apr 30, 2019 3:29 am
- Forum: Member's Rides, Projects, and Builds
- Topic: 1965 Corsa clone, but a sweeeeeet one
- Replies: 305
- Views: 64762
Re: 1965 Corsa clone, but a sweeeeeet one
Backed the timing off a tiny bit, helps tame the surging under low RPM/high vacuum all in ignition timing situations. Haven't done anything but drive it lately.
- Tue Feb 26, 2019 3:30 pm
- Forum: Member's Rides, Projects, and Builds
- Topic: 1966 corsa
- Replies: 9
- Views: 1648
Re: 1966 corsa
Nice! 66 Corsa.
- Tue Jan 29, 2019 8:43 am
- Forum: Member's Rides, Projects, and Builds
- Topic: Choke Adjustment
- Replies: 16
- Views: 3853
Re: Choke Adjustment
Progress! New pull-offs will have you smiling when you don't have to jump out any more.
- Thu Jan 24, 2019 3:27 pm
- Forum: Corvair of the Month Calendar Page (Sponsored by Clark's Corvair Parts)
- Topic: VOTE - Corvair of the Month January 2019
- Replies: 10
- Views: 6237
- Fri Jan 18, 2019 3:58 pm
- Forum: Introductions
- Topic: Wannabe Corvair owner!
- Replies: 5
- Views: 787
Re: Wannabe Corvair owner!
Let us know what part of the US or elsewhere you hail from.
- Fri Jan 18, 2019 3:57 pm
- Forum: Corvair of the Month Calendar Page (Sponsored by Clark's Corvair Parts)
- Topic: VOTE - Corvair of the Month January 2019
- Replies: 10
- Views: 6237
Re: ENTER - Corvair of the Month January 2019
When do we vote? :)
- Wed Jan 16, 2019 10:23 am
- Forum: Introductions
- Topic: New corvair owner 64 convert
- Replies: 17
- Views: 1900
Re: New corvair owner 64 convert
I do work on Wednesdays and Thursdays unfortunately, I have weekends off, you work weekends?
- Tue Jan 08, 2019 3:20 pm
- Forum: Corvair of the Year Calendar Page (Sponsored by Clark's Corvair Parts)
- Topic: Vote for 1965-1969 Corvair of the Year 2018
- Replies: 7
- Views: 15501
Re: Vote for 1965-1969 Corvair of the Year 2018
Yeah, but in a Corvair guy kind of way. :)
- Tue Jan 08, 2019 3:19 pm
- Forum: Introductions
- Topic: New corvair owner 64 convert
- Replies: 17
- Views: 1900
Re: New corvair owner 64 convert
Didn't go far from Merlin to GP. Awesome, would love to come down and check it out.