Search found 234 matches
- Wed Sep 25, 2019 2:37 pm
- Forum: Ask your Mechanical Questions here
- Topic: AN10 Oil Cooler Lines Setup
- Replies: 1
- Views: 543
AN10 Oil Cooler Lines Setup
Hi, all. I am building a 110 corvair engine and found the aluminum external oil cooler adapter block on Clark's website. The block came with a barbed fitting that would work for rubber hoses. I want to run an10 braided lines to my cooler so I ordered some of these aluminum fittings. The inside diame...
- Sun Aug 04, 2019 1:23 pm
- Forum: Ask your Mechanical Questions here
- Topic: Trans mounts
- Replies: 1
- Views: 1906
Trans mounts
I have a 65 Monza and the trans mounts need replacing. The car is an automatic from factory and I am converting it to a manual transmission from a 64 4 speed car. Do I need to use the 1964 mounts to install on my 65 car?
Sent from my ONEPLUS A6000 using Corvair Forum mobile app
Sent from my ONEPLUS A6000 using Corvair Forum mobile app
- Sun Nov 18, 2018 2:49 pm
- Forum: Ask your Mechanical Questions here
- Topic: Engine Cases with Different Numbers
- Replies: 7
- Views: 598
Re: Engine Cases with Different Numbers
Yea it’s kind of weird because the condition of one half of the block is in mint condition while the other half looked like it was barely usable with all the corrosion
Sent from my iPhone using Corvair Forum mobile app
Sent from my iPhone using Corvair Forum mobile app
- Sat Nov 17, 2018 6:28 pm
- Forum: Ask your Mechanical Questions here
- Topic: Engine Cases with Different Numbers
- Replies: 7
- Views: 598
Engine Cases with Different Numbers
I recently bought a spare set of engine halves and when I got them they had different numbers on them. One half has 3819615 and the other half has 3819616. There is a code on top where the crankcase cover goes that reads T0302RA. Anybody know what is going on? Is one half from a different engine? Im...
- Tue Nov 06, 2018 10:34 pm
- Forum: Ask your Mechanical Questions here
- Topic: Converting from 4 barrel to 2 barrel carb?
- Replies: 10
- Views: 2554
Re: Converting from 4 barrel to 2 barrel carb?
I have a 110 engine and was wandering if I could put the 390 Holley on there with 2 plenum center mount?
Sent from my iPhone using Corvair Forum mobile app
Sent from my iPhone using Corvair Forum mobile app
- Fri Nov 02, 2018 3:21 pm
- Forum: Ask your Mechanical Questions here
- Topic: Engine Case Upper Head Studs
- Replies: 8
- Views: 1246
Re: Engine Case Upper Head Studs
It also looks to be tapered because it only threads in one thread on a 7/16-14 but then stops. Do I need to heat up the engine case then install the stud?
Sent from my iPhone using Corvair Forum mobile app
Sent from my iPhone using Corvair Forum mobile app
- Fri Nov 02, 2018 2:23 pm
- Forum: Ask your Mechanical Questions here
- Topic: Engine Case Upper Head Studs
- Replies: 8
- Views: 1246
Re: Engine Case Upper Head Studs
It looks as if the threads are 7/16-14
How do I know for sure?
Sent from my iPhone using Corvair Forum mobile app
How do I know for sure?
Sent from my iPhone using Corvair Forum mobile app
- Sat Oct 20, 2018 4:40 pm
- Forum: Ask your Mechanical Questions here
- Topic: Engine Case Upper Head Studs
- Replies: 8
- Views: 1246
Engine Case Upper Head Studs
I am working on an upper stud that broke off while I was trying to remove it because the threads are rusted off. I see that Clark’s has a super stud that is stronger than originals. It says I just need a standard gh3 tap. Does anyone know what size drill bit and tap they used for these studs? IMG_00...
- Sun Aug 27, 2017 6:27 pm
- Forum: Ask your Mechanical Questions here
- Topic: Exhaust Valve Questions
- Replies: 2
- Views: 394
Re: Exhaust Valve Questions
Have you ever ground it down all the way to just enough material for the guide?
Sent from my iPhone using Corvair Forum mobile app
Sent from my iPhone using Corvair Forum mobile app
- Fri Aug 25, 2017 7:38 pm
- Forum: Ask your Mechanical Questions here
- Topic: Exhaust Valve Questions
- Replies: 2
- Views: 394
Exhaust Valve Questions
I was just looking inside the exhaust chambers for my 1964 110 hp head and it looks like a kink in the exhaust side! Has anyone ever milled that groove off down near to the guides because I don't know how the exhaust can get through there? It's like a 90 degree turn. Sent from my iPhone using Corvai...
- Tue Aug 15, 2017 12:27 pm
- Forum: DIY - Explanations and Demonstrations
- Topic: shift boot install problem
- Replies: 4
- Views: 1050
Re: shift boot install problem
Does anyone know how to properly reinstall a shifter assembly? Does the seat with one tang have to be on a certain side?
Sent from my iPhone using Corvair Forum mobile app
Sent from my iPhone using Corvair Forum mobile app
- Sun Aug 13, 2017 3:37 pm
- Forum: Ask your Mechanical Questions here
- Topic: Valve Questions
- Replies: 6
- Views: 889
Re: Valve Questions
Is there such a thing as tulip valves for a corvair? Also, are clarks tufftrided valves any good? Just need good strong valve for a street use 110 hp engine.
Sent from my iPhone using Corvair Forum mobile app
Sent from my iPhone using Corvair Forum mobile app
- Sun Aug 06, 2017 9:02 pm
- Forum: Ask your Mechanical Questions here
- Topic: Engine rebuild
- Replies: 18
- Views: 3696
Re: Engine rebuild
Ok if I find a 65-9 engine what parts can I use off this 64 engine?
Sent from my iPhone using Corvair Forum mobile app
Sent from my iPhone using Corvair Forum mobile app
- Sat Aug 05, 2017 7:56 am
- Forum: Ask your Mechanical Questions here
- Topic: Engine rebuild
- Replies: 18
- Views: 3696
Re: Engine rebuild
If I were to get the Isky 260 cam would that make the compression higher since that cam is rated at 9.5:1
Sent from my iPhone using Corvair Forum mobile app
Sent from my iPhone using Corvair Forum mobile app
- Fri Aug 04, 2017 6:09 pm
- Forum: Ask your Mechanical Questions here
- Topic: Engine rebuild
- Replies: 18
- Views: 3696
Re: Engine rebuild
Daily driver no drag racer just for driving on the street
Sent from my iPhone using Corvair Forum mobile app
Sent from my iPhone using Corvair Forum mobile app
- Fri Aug 04, 2017 5:35 pm
- Forum: Ask your Mechanical Questions here
- Topic: Engine rebuild
- Replies: 18
- Views: 3696
Re: Engine rebuild
What cam could I use on this engine to get better results?
Sent from my iPhone using Corvair Forum mobile app
Sent from my iPhone using Corvair Forum mobile app