Search found 31 matches
- Tue May 14, 2024 12:02 am
- Forum: Ask your Mechanical Questions here
- Topic: LM Front Speaker Replacement options?
- Replies: 16
- Views: 294
Re: LM Front Speaker Replacement options?
I received an Email today from OER - an older parts specialist. (I have supplied them with some other parts.) They are listing several new 10 Ohm speakers for mid-60s GM cars, including a couple of 6 x 10s. . They are not listing a Corvair specific one, but one looks like it would push up into place...
- Sat May 04, 2024 6:57 pm
- Forum: Corvair Talk
- Topic: Broken Rocker Stud
- Replies: 22
- Views: 548
Re: Broken Rocker Stud
Chevy slightly changed the design of the rocker near the end of production. All stock in the replacement part warehouses eventually changed to the new style. The later design had a wider, but shorter contact face for the valve tip. I don't believe there was a change to the ratios. I always save the ...
- Sun Apr 28, 2024 4:58 pm
- Forum: DIY - Explanations and Demonstrations
- Topic: LM Corvair Instrument Panel Gauge Checks
- Replies: 5
- Views: 188
Re: LM Corvair Instrument Panel Gauge Checks
Very Nice, Al. Can you hook up something to Calibrate the tach?
- Fri Apr 26, 2024 7:57 pm
- Forum: Member's Rides, Projects, and Builds
- Topic: My story on the Electronic distributor
- Replies: 6
- Views: 300
Re: My story on the Electronic distributor
I tested each one before shipping. They should be fine. I can tell you how to test them before you install them if you are concerned. I built a cool test unit. I can test either type of dist. But it is easy for you to check in your garage.
- Thu Apr 25, 2024 11:15 pm
- Forum: Member's Rides, Projects, and Builds
- Topic: My story on the Electronic distributor
- Replies: 6
- Views: 300
My story on the Electronic distributor
Okay – my story on the “Stinger” distributor. Starting in the late 80’s, I started going back to the SEMA show every year. I had attended with Bill Fisher and HP Books back in the 70s, when they were supplying the ‘How to Hot Rod Corvair Engines’ book. I answered questions in the booth a bit. In the...
- Tue Apr 23, 2024 6:24 pm
- Forum: Ask your Mechanical Questions here
- Topic: I need help understanding the engine
- Replies: 17
- Views: 517
Re: I need help understanding the engine
For the first-time Corvair mechanic, the Corvair Basics book may be a real help. Join Corsa and you get the book with your joining membership. Lots of good info from the knowledgeable Corvair folks. Check with Corsa for membership info at "www.corvair.org" -
- Sun Apr 21, 2024 12:24 pm
- Forum: Ask your Mechanical Questions here
- Topic: Melting wires, simple question
- Replies: 77
- Views: 1905
Re: Melting wires, simple question
Well, yes and No, Frank, on the plug gaps. I still suggest .035 on the Corvair, no matter which ignition. This is worth a read: (from the Internet) "Origins and Purpose of HEI: The GM HEI system was not initially developed as a performance ignition system. Instead, its primary purpose was to ef...
- Sat Apr 20, 2024 9:44 am
- Forum: Ask your Mechanical Questions here
- Topic: Melting wires, simple question
- Replies: 77
- Views: 1905
Re: Melting wires, simple question
"Almost" any coil will fire the plugs, when properly triggered. In my experience, and with a few users reminding me of electronics math, I changed my recommendation (many years ago, now) to the 3.0 Ohm coil. The higher the resistance rating - actually the total resistance of the coil energ...
- Tue Apr 16, 2024 10:45 am
- Forum: Ask your Mechanical Questions here
- Topic: Melting wires, simple question
- Replies: 77
- Views: 1905
Re: Melting wires, simple question
For reference. With the TSP distributor, I recommend bypassing the stock resistance wire and feeding both the coil and the distributor full battery voltage. I also recommend using ONLY a 3.0 Ohm coil with that set-up. With a battery voltage feed, you will still have plenty of spark output, and you w...
- Tue Apr 02, 2024 8:44 pm
- Forum: Member's Rides, Projects, and Builds
- Topic: Working on the Corvair again.
- Replies: 2
- Views: 151
Working on the Corvair again.
Wonder of wonders, I actually did work on my Corvair today. (65 Monza 140 4-speed). This morning I drove it over to Mel's VairMart in Santa Clara, CA and put it up on his lift for a few hours. Since it had been sitting for 15 years when I got it, I had already gone through most of the systems about ...
- Sun Mar 31, 2024 2:06 pm
- Forum: Introductions
- Topic: EZCARLIFT Question
- Replies: 16
- Views: 569
Re: EZCARLIFT Question
On the second lift of my Corvair on the EZ Car lift -correctly lubed - my Black & Decker 3/8" HD corded drill started putting out the "Ozone" electric smell, though it didn't slow down. I decided to buy a "real" drill and found this. This sucker will rip your wrist off.
- Sat Mar 30, 2024 6:26 pm
- Forum: Introductions
- Topic: EZCARLIFT Question
- Replies: 16
- Views: 569
Re: EZCARLIFT Question
Another data point- buy the most powerful wired drill you can find. Trust me. Forget about any cordless.
- Mon Mar 25, 2024 12:48 pm
- Forum: Corvair Talk
- Topic: "Unsafe To Carry"
- Replies: 9
- Views: 1280
Re: "Unsafe To Carry"
You could say it's a Chevy Monza, not positive of the year. Not telling a lie.
- Sun Mar 24, 2024 9:45 pm
- Forum: Ask your Mechanical Questions here
- Topic: Telescoping Steering Wheel
- Replies: 22
- Views: 3299
Re: Telescoping Steering Wheel
You tube on disassembly/reassembly of the 65-66 tele column:
- Fri Mar 22, 2024 8:57 pm
- Forum: Ask your Mechanical Questions here
- Topic: Which spark plug wires?
- Replies: 24
- Views: 2346
Re: Which spark plug wires?
Many colors, no waiting! -Seth
- Thu Feb 29, 2024 8:17 pm
- Forum: Corvair Talk
- Topic: Question about using a tow bar
- Replies: 39
- Views: 969
Re: Question about using a tow bar
If you tell U-haul you are going to carry a Chevy Monza, but you are not sure which year it was built, you are not lying. <grin>