Search found 430 matches
- Thu Oct 21, 2021 7:10 am
- Forum: Corvair Talk
- Topic: Bracket?
- Replies: 2
- Views: 415
Re: Bracket?
Yes, from the pictures you posted of it being loaded onto a trailer, that bracket is for holding the triangle washer fluid refill bottle. That's also not the correct engine deck lid....but you knew that. Vairy nice car though!
- Sat Oct 09, 2021 6:48 am
- Forum: Ask your Mechanical Questions here
- Topic: Inlet needle and seat question.
- Replies: 6
- Views: 663
Re: Inlet needle and seat question.
Just realized my throttle pumps I removed had no springs or retaining clips on them. My kit did not come with them either, your supposed to swap them over to the new ones, there was only the lower thinner spring in the bottom :banghead: Pm me your address and I'll get a couple in the mail to you.
- Wed Oct 06, 2021 1:13 pm
- Forum: Ask your Mechanical Questions here
- Topic: choke rod hole plugged
- Replies: 5
- Views: 526
Re: choke rod hole plugged
I have drilled 61 heads to install automatic chokes. Didn't hit anything that leaked anything.
- Wed Oct 06, 2021 5:58 am
- Forum: Introductions
- Topic: I inherited 12 Corvairs last week
- Replies: 10
- Views: 1144
Re: I inherited 12 Corvairs last week
Joel......PM Sent.
- Wed Sep 29, 2021 5:22 am
- Forum: Ask your Mechanical Questions here
- Topic: Loose rocker arm
- Replies: 16
- Views: 1292
Re: Loose rocker arm
Back off the inner set screw. Adjust the rocker as necessary. Snug down set screw as best you can while holding the outer hex. While holding the set screw, tighten the outer hex a lil further.
- Fri Sep 24, 2021 7:12 am
- Forum: Member's Rides, Projects, and Builds
- Topic: Corvair Lakewood 61 - NL
- Replies: 552
- Views: 126247
Re: Corvair Lakewood 61 - NL
That's how you eat (complete) an elephant (project). One bite at a time! Great work and a fine example to the rest of us.
- Fri Sep 03, 2021 6:24 am
- Forum: Member's Rides, Projects, and Builds
- Topic: Corvair Lakewood 61 - NL
- Replies: 552
- Views: 126247
Re: Corvair Lakewood 61 - NL
On my Lakewood, the license plate lights will not come on if the rear engine access door is not latched. That's how it gets its ground.
- Wed Sep 01, 2021 7:08 am
- Forum: Ask your Mechanical Questions here
- Topic: Odd Hesitation Issue
- Replies: 33
- Views: 3272
Re: Odd Hesitation Issue
Doubtful but possible. The only wear part that isn't normally replaced is the throttle shaft. It's more likely something was missed on the rebuild.
- Tue Aug 31, 2021 7:10 am
- Forum: Ask your Mechanical Questions here
- Topic: Jack label
- Replies: 11
- Views: 833
Re: Jack label
FREE FREE https://ssl.corvair.com//user-cgi/search.cgi?part=C9837 FREE
Did I mention it's FREE?
Did I mention it's FREE?
- Sat Aug 21, 2021 7:23 am
- Forum: Ask your Mechanical Questions here
- Topic: The Big Sleep
- Replies: 10
- Views: 570
Re: The Big Sleep
I don't believe any of the above failures will still allow you to get 115-125 p.s.i. compression readings.
- Sat Aug 21, 2021 6:28 am
- Forum: Member's Rides, Projects, and Builds
- Topic: My 68 cruiser project
- Replies: 15
- Views: 1622
Re: My 68 cruiser project
This all depends of course on what left lower damper door sheet metal you have. It is differant to fit the 12 plate cooler or the 8 plate/folded fin version. As yet there have been no pictures of it.
- Fri Aug 20, 2021 9:22 am
- Forum: Member's Rides, Projects, and Builds
- Topic: My 68 cruiser project
- Replies: 15
- Views: 1622
Re: My 68 cruiser project
I was referring to a good air seal on the top and bottom shrouding. You have a mismatch of parts there.
- Fri Aug 20, 2021 5:31 am
- Forum: Member's Rides, Projects, and Builds
- Topic: My 68 cruiser project
- Replies: 15
- Views: 1622
Re: My 68 cruiser project
Vairy nice work. Make sure you have a good seal on the oil cooler cover. Or go to the folded fin version.
Cruise that baby!
Cruise that baby!
- Sat Aug 07, 2021 6:23 pm
- Forum: Ask your Mechanical Questions here
- Topic: Direction switch grip.
- Replies: 2
- Views: 239
Re: Direction switch grip.
Bend the tab that you depress to install the wire outward a bit. It will then put more pressure on the wire.
- Sat Jul 31, 2021 8:01 pm
- Forum: Ask your Mechanical Questions here
- Topic: Engine woes
- Replies: 11
- Views: 789
Re: Engine woes
1. Blocked crossover intake tube on that side.
2. Someone removed the crossover, turbo and carb. for whatever reason. Rag or plug was put in the head intake port for safety. Blocking plug was forgotten when the crossover was reinstalled.
2. Someone removed the crossover, turbo and carb. for whatever reason. Rag or plug was put in the head intake port for safety. Blocking plug was forgotten when the crossover was reinstalled.
- Sat Jul 31, 2021 4:29 am
- Forum: Ask your Mechanical Questions here
- Topic: strange canisters
- Replies: 16
- Views: 1762
Re: strange canisters
JohnDB, Check Your PM's.