Search found 57 matches

by dick2256
Wed Feb 15, 2017 8:10 am
Forum: Ask your Mechanical Questions here
Topic: carburator stud bolts thread sizes
Replies: 2
Views: 110

Re: carburator stud bolts thread sizes

Thanks Jerry
I looked at them under my magnifier ands there was a little rust in the threads
and after I run them through a wire brush wheel they worked greet
Thanks
by dick2256
Tue Feb 14, 2017 4:32 pm
Forum: Ask your Mechanical Questions here
Topic: carburator stud bolts thread sizes
Replies: 2
Views: 110

carburator stud bolts thread sizes

what are the carburetor stud bolt sizes
the block thread is a cuorse thread but the nut end is a fine thread
but I don't think either are standard sizes
by dick2256
Sat Feb 11, 2017 2:28 pm
Forum: Ask your Mechanical Questions here
Topic: cover that holds the alternator
Replies: 10
Views: 302

Re: cover that holds the alternator

I think so to my son works on a lot of chainsaws and small 2 cycle engines and that looks like something out of one of those. anyway I put that cover back on and we will find out in a week or so if there is a part missing I have some stripped threads in 5 or 6 pan bolt threads and then I am going to...
by dick2256
Sat Feb 11, 2017 12:08 pm
Forum: Ask your Mechanical Questions here
Topic: cover that holds the alternator
Replies: 10
Views: 302

Re: cover that holds the alternator

I don't agree with you his picture and mine look the same to me
the screen and is still there undisturbed and I look to the right there is another place where I can see the spring there
by dick2256
Sat Feb 11, 2017 8:34 am
Forum: Ask your Mechanical Questions here
Topic: cover that holds the alternator
Replies: 10
Views: 302

Re: cover that holds the alternator

I sent a couple more pictures of the underside of my cover plate and a picture of the top of it so you will understand what we did tried again to get a better picture of that piece but just don't have a very good camera. as you can see in the underside view the part scotty was talking is in where hi...
by dick2256
Fri Feb 10, 2017 4:06 pm
Forum: Ask your Mechanical Questions here
Topic: cover that holds the alternator
Replies: 10
Views: 302

Re: cover that holds the alternator

mine has been drilled out and a couple hose adapter go to the oil filter and to another larger cooler we did that back in the early 70's but I don't remember this part will attach a couple pictures of the part but they don't show up very good I said it was yellow plastic but I was wrong it is orange...
by dick2256
Fri Feb 10, 2017 2:23 pm
Forum: Ask your Mechanical Questions here
Topic: cover that holds the alternator
Replies: 10
Views: 302

cover that holds the alternator

I took the aluminum plate off that hold the alternator and the fuel pump off to clean it and when I got done there was a filter laying in the bucket I had the diesel fuel in and I am not sure where it goes there is one small fixed filter on that cover and one on the main body of the motor this looks...
by dick2256
Tue Feb 07, 2017 3:03 pm
Forum: Ask your Mechanical Questions here
Topic: metal
Replies: 5
Views: 207

Re: metal

thanks that is what I will do
by dick2256
Tue Feb 07, 2017 2:14 pm
Forum: Ask your Mechanical Questions here
Topic: metal
Replies: 5
Views: 207

Re: metal

I'll open up the oil pump when I get another warm day and see what it looks like
by dick2256
Tue Feb 07, 2017 9:41 am
Forum: Ask your Mechanical Questions here
Topic: metal
Replies: 5
Views: 207

Re: metal

no I never had the blower cover off
they are very small particles if they
made it through an open intake valve could they somehow get into the oil.
do you think I should pull the blower cover and see what the bearings look
or just put it back together and run it the way it is and see what happens
by dick2256
Tue Feb 07, 2017 5:26 am
Forum: Ask your Mechanical Questions here
Topic: metal
Replies: 5
Views: 207

metal

I pulled the oil pan off to install a new gasket and found a few very small pieces of aluminum
I think it came from when I put a helicoil in a stripped out p0lug hole
any thing I need to do to try to clean the oil lines better
by dick2256
Fri Feb 03, 2017 3:49 am
Forum: Ask your Mechanical Questions here
Topic: lifter removal
Replies: 9
Views: 271

Re: lifter removal

I am only removing 2 oil return tubes at a time
so and can't I put those back to the 30 ft pounds and repeat to the next 2
I am not removing the heads only removing the rocker arms so I can install a new seal and the O-rings on each end of the oil return tubes
by dick2256
Thu Feb 02, 2017 4:29 pm
Forum: Ask your Mechanical Questions here
Topic: lifter removal
Replies: 9
Views: 271

Re: lifter removal

ok sounds good to me thanks
by dick2256
Thu Feb 02, 2017 12:35 pm
Forum: Ask your Mechanical Questions here
Topic: lifter removal
Replies: 9
Views: 271

Re: lifter removal

magnet worked great for pulling the lifters out
Now where can I find the tork specks for 1965 110hp engine
I have been changing the oil seals in the oil return tubes and am not sure what the thing the rocker arm mounts onto
is called
by dick2256
Wed Feb 01, 2017 1:43 pm
Forum: Ask your Mechanical Questions here
Topic: lifter removal
Replies: 9
Views: 271

lifter removal

Is there an easy way to remove the lifters
by dick2256
Sat Jan 21, 2017 11:55 am
Forum: Ask your Mechanical Questions here
Topic: oil seal
Replies: 1
Views: 107

oil seal

what do they call the O-ring that sets under the rocker arm stud
6 of them per head

Go to advanced search